-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
The Partnership: Design Engineers and PCB Designers
May 23, 2016 | Andy Shaughnessy, PCBDesign007Estimated reading time: 3 minutes
Randy Faucette is founder, president and director of engineering at Better Boards Inc. in Cary, North Carolina. Founded in 2003, Better Boards provides electrical engineering, PCB design, signal and power integrity analysis, and a variety of other services. I asked Randy to talk about some of the occasional tension between PCB designers and design engineers, and what he thinks can be done to help open the lines of communication.
Andy Shaughnessy: Randy, tell us a little bit about your company and how you operate.
Randy Faucette: Better Boards is a PCB design and engineering services company. We specialize in all aspects of PCB design, but also provide electrical and mechanical engineering, software/firmware development, prototype and small-volume production manufacturing, and many types of analysis including failure mode, root cause, thermal, crosstalk and power integrity. We use a breadth of design tools including Cadence Allegro, Altium, Mentor Expedition and PADS. Our customers range from large companies like Lenovo and Cree to small entrepreneurs. We perform finite services our customers define to full development of products from concept to production. We cover many industries, such as medical, commercial, consumer, telco, and space/military.
Shaughnessy: A recent survey of our PCB designer readers found that there’s often friction between PCB designers and engineers. Some designers say, only half-jokingly, that their EEs are their biggest challenge. Why do you think there’s such disconnect at some companies?
Faucette: We have not found that to be true here at Better Boards. We approach PCB design from an engineering standpoint. The PCB designer should not just be a tools jockey hoping that engineering will tell them where to put parts and how to hook them up. The PCB designer should understand how the circuits flow, understand the different types of interfaces and how those need to be treated on the board, and understand the manufacturing aspects as well (including test). The only challenge we experience with engineering honestly is playing the role of middleman between engineering and manufacturing. Engineering may want parts located too close to another component or too close to a through-hole pin, not allowing a proper wave soldering operation to be performed. Those drive costs and can affect reliability. If the layout designer is effective, engineering is happy and manufacturing is also happy. That makes the boss happy!
Shaughnessy: What do you think is the proper role for a PCB design engineer?
Faucette: Outside of creating a correct schematic, the PCB design engineer needs to effectively communicate ALL of the requirements of the board and then review the board once designed to ensure all the requirements have been achieved. Some examples of requirements would be interface impedances, timing rules, and power requirements. It’s also important to identify high-speed nets, clock lines, sensitive nets/circuits, high-current buses, thermally hot nodes, high switching loops. The stackup is critical in most designs today and this must be considered early. One thing that should be communicated early on is the environment of the product and the expected reliability. The temperature and humidity can drive what component packages to use (or more importantly what not to use). The reliability can drive board technology and spacings. The best way to communicate all the rules is in a PCB requirements document. This is the scope of the layout. If it’s in the document, it’s important. It also removes the flurry of comments, instructions, and “Oh, BTWs” that tend to arrive in various emails and in cubicle conversations. It’s a captive, living document to keep everyone straight. It’s also it a perfect checklist at review time.
To read this entire article, which appeared in the April 2016 issue of The PCB Design Magazine, click here.
Suggested Items
GlobalFoundries Commits to Achieving Net Zero Emissions and Carbon-Neutral Power by 2050
04/23/2024 | GlobalFoundriesGlobalFoundries (GF) is furthering its commitment to sustainable operations and fighting climate change with the announcement of two new long-term goals to achieve net-zero greenhouse gas (GHG) emissions and 100% carbon-neutral power by 2050.
ROHM Group Company SiCrystal and STMicroelectronics Expand Silicon Carbide Wafer Supply Agreement
04/23/2024 | ROHMROHM and STMicroelectronics, a global semiconductor leader serving customers across the spectrum of electronics applications, announced today the expansion of the existing multi-year, long-term 150mm silicon carbide (SiC) substrate wafers supply agreement with SiCrystal, a ROHM group company.
IDTechEx Report Unveils 3D Electronics Status and Opportunities
04/22/2024 | PRNewswire3D electronics is an emerging manufacturing approach that enables electronics to be integrated within or onto the surface of objects. 3D electronic manufacturing techniques empower new features, including mass customizability, greater integration, and improved sustainability in the electronics industry.
Altus Group Helps BitBox Unlock Productivity and Efficiency Gains with New Reflow Oven
04/22/2024 | Altus GroupAltus Group, a leading provider of capital equipment, has recently assisted BitBox, a UK-based electronics design, engineering and manufacturing company in upgrading its operations with the implementation of a new reflow oven from Heller Industries.
Growth Potential: Electronics Manufacturing Driving Massive Surge in Manufacturing Investment
04/22/2024 | Shawn DuBravac, IPCIn the early months of the pandemic, investment in manufacturing infrastructure, such as plants and production facilities, declined sharply. Real investment dropped over 11%, before finally recovering to pre-pandemic levels in the first half of 2022. Over the past two years, however, several factors have combined to drive manufacturing investment to record levels.